JD, JV, XP and XV series

does anyone still have a XV-5080?

does anyone still have a XV-5080?

16 Apr 2019, 04:14
can you tell me what amp the fuse is in the plug please?

thanks.

Re: does anyone still have a XV-5080?

16 Apr 2019, 11:53
I have a XV-5080 wired for 110 AC (U.S.) there is no external fuse, on back of unit or in power cord itself (if that's what your asking) and no fuse(s) internal either at least that I can see from the service manual.

Re: does anyone still have a XV-5080?

17 Apr 2019, 04:02
no fuse in the plug?

it wouldn't power on without a fuse. you need the fuse to complete the circuit...

Re: does anyone still have a XV-5080?

17 Apr 2019, 15:27
All I can say if YOUR your power cord has an in-line fuse in it should be marked when you remove it to tell you AMPS @ voltage. What are the markings?

-----------------------------------------------------------
Before we go on please remember I’m using a 110 VAC USA XV-5080 unit and all I need is a standard 3-prong (unfused) cord. I can use any standard 3-prong cord like these and I actually do. I use a 3-foot one not the supplied 6 footer because unit it’s close to regulated power strip in rack
https://www.amazon.com/TNP-Universal-Power-Cord-Feet/dp/B01EYDGO12/ref=sr_1_3?qid=1555529146&refinements=p_n_feature_keywords_browse-bin%3A3606203011&s=aht&sr=1-3

Maybe the other cord sets, for units shipped to other countries, had in-line fusing (this is list from Service Manual page 7)

00894367 AC CORD SET 100V SP18A+IS14 VCTF2X0.75 1
00894378 AC CORD SET 120V SP301+IS14 SJT18/3 1 (NOTE this USA and like MINE it is NOT FUSED )
00894389 AC CORD SET 230V SP22+IS14 H05VV-F3G1.0 1
00907001 AC CORD SET 240VE KP-610 GTTBS-3 KS-31A 1
23495124 AC CORD SET 240VA SC-144-JO1 ES303-
10HMA

Now back to what you said, in general you do not NEED a fuse to “complete any circuit” you may need or want a fuse if you want to PROTECT a circuit that doesn’t have any other means of protection from internal unit over currents, shorts, etc. You may also DESIGN a circuit in such a way that it requires a fuse at some point in voltage path. But a fuses only purpose is to keep the unit from allowing too much internal destruction of unrelated circuits, or even too much destruction of the very circuit causing too much current draw.

I was going to take a picture of my XV-5080’s back to show it has no fuses there but no need – look at Users Manual page 14 – (diagram of back of unit is same as my unit) you can see there is NO FUSE, at least externally.

THE XV-5080’s power supply, is nothing more than a self-contained switching regulator takes 100, 115, 230, or 240 VAC and converts those AC voltages into DC: +15 VDC, -15 VDC and +5VDC. So any “protection” must be performed in that module – because in the schematics there are no fuses anywhere: see Service Manual. If you doubt me – open up your unit and look for fuses. BTW while you are in there you may want to remove and replace the CR2032 battery on Main Board– I’m sure it’s the original and WAY OVER 10 years old. However, make sure you back up your XV 5080 user memory first to external device like SM card.

Re: does anyone still have a XV-5080?

18 Apr 2019, 04:17
hi thanks for taking the time.

in am in UK. i got a EU model with no plug/power lead. it says 100v on the back, but i read online about the internal switching power supply so it could take UK 240v.

so i just used an old PC power lead that i had and put a 3A fuse in it, since that was the lowest fuse i had and lower is safer than higher (easier to blow if it needs to blow)

i was sure you needed fuses in plugs to complete the circuit... guess not. silly me.

before buying i got the technician put a new battery in (and he photo'd it for proof) so all good there!

so i guess i am safe running the plug with the 3A fuse?

Re: does anyone still have a XV-5080?

18 Apr 2019, 18:26
3 AMPS is WAY TOO LARGE if it is indeed a in-line fused power plug.

Unit is a max of 25 WATTs (see manual)

In UK you are running 3-phase 240 at 50 hertz - so a unit that draws the MAX 25 watts (max watts is 25 - see manual) so about 0.1042 Amps – so largest I would even consider is a 0.2 AMP fuse; however, the BEST would be a fast blow 0.1 amp (just a hair SMALLER than worst case amp draw)

current = power ÷ voltage

x= 25 watts /240 volts = .104 AMPS

Re: does anyone still have a XV-5080?

12 Sep 2020, 18:57
Hi - sorry to hijack the thread but does anyone have instructions on how to change the internal 5080 battery? It isn't shown in the service manual. I know it resides on the main board but there's no actual detail as to the exact location and how best to access it. I did this on my 2080 and accessed the battery by removing the expansion cover and then removing the expansion board. Is this the way in for the 5080 too?

Thanks.

Re: does anyone still have a XV-5080?

19 Sep 2020, 08:25
UnderTheStairs wrote:
Hi - sorry to hijack the thread but does anyone have instructions on how to change the internal 5080 battery?
Check out this vid for XV-5080 internals:
https://www.youtube.com/watch?v=4nW7qyra8vM
here's the original thread at Gearslutz, with more pictures:
https://www.gearslutz.com/board/electronic-music-instruments-and-electronic-music-production/1133675-xv-5080-quot-static-noise-quot-solution.html

Swapping the battery should be very straightforward and quite similar to the JV-2080 process.
Which you can find here;
https://blog.sector101.co.uk/2020/08/15/roland-jv-2080-battery-replacement/

As usual, just remember to backup your user patches first.

← Back to JD, JV, XP and XV series