Fantom-S and Fantom-X

Fantom X Color LCD

Fantom X Color LCD

23 Apr 2004, 16:51
Have any other FX owners been experiencing this? My color LCD screen seems to be somewhat dim. I've had the keyboard for about a month now and the LCD seems rather dark. I've tried using the contrast adjustment but no improvement. Just the other day, the screen blinked and got much brighter. It seems to come and go now.

Are the LCD screens sensitive to temperature change? I have my FX in the basement where the temp is somewhat cooler than in the rest of the house.

Re: Fantom X Color LCD

23 Apr 2004, 19:12
i'd assume temperature has something to do with it since i recall there's a notice sheet that come with the fantom-x: depending on the location, brightness of the lcd backlight might be affected, or something like that.

------------------------------
I Play for God
------------------------------
I Play for God

Re: Fantom X Color LCD

25 Apr 2004, 03:25
Hi jrosand. I have a FX8 and I haven't been experiencing any difficulties with my color LCD, especially with it changing illumination levels on and off. My FX is next to a closed window with the blinds closed all the time. It's upstairs and the temperature gets up to about 78 degrees Fahrenheit (25 degrees Celsius) and the low (since I've had it for a little over a month) has been maybe 70 F (21 C). Temperature, in either extreme will affect the LCD, but if it's quickly going from dim to bright, I'd guess it's in need of repair.

Nathan Sheldon
http://www.nathansheldon.com/
Regards,

Nathan Sheldon
http://www.nathansheldon.com/

Re: Fantom X Color LCD

25 Apr 2004, 11:16
Jrosand,

It's difficult to give you really good advice without seeing your FX in real live next to another one, but it sounds a bit like the backlight CFTs (Cold Fluorescence Tube) are flaky. CFTs are very similar to your average neon light and you know how sometimes these lights don't start properly or stay dim for a long time? Could be the same thing here. Does the backlight seem to flicker (the LCD as a whole does flicker a little bit I think so this could be difficult to determine).

The contrast knob won't actually change the brightness, it only regulates a bias voltage supplied to the liquid crystals that rotate the polarized light, thereby changing the angle from which the display is best viewed.

Try comparing your display to that of another FX. If it's significantly different (less bright) I'd have it looked after.
http://www.youtube.com/watch?v=TXz0UkVBZPQ
TOYZ in 60 seconds (short live video of my progrock band on YouTube)

FX color display

25 Apr 2004, 18:30
Thank you all for your information. My screen is not flickering per say. It's only on rare occassions that it blinks & becomes brighter. It seems to occur when I move my keyboard from a cool environment to a warmer and brighter environment. I reintiailized my keyboard once and got the brighter screen upon reboot.

I've already got a RMA # from Roland concerning this. I'm afraid I led the service tech to think that this was a very frequently occurring problem.

I think I'll live with it for awhile and see if others experience similar problems.......

Thanks again.

Re: Fantom X Color LCD

26 Apr 2004, 18:09
I was just about to post a thread about my display... I got my new X6 home last monday and powered her up and within minutes the display would begin to lighten and darken just a little bit but it did it continuosly, almost like a pulsating effect. So I boxed her up and brought her back in to the GC near me and they gave me a new one. Now with my second X6, I get a slight variation in brightness only every once in a while, like every few minutes it may dip just a tad in brightness and return to where it was...

Now after reading Arjan's post where he mentions "the LCD as a whole does flicker a little bit..." I assume this is normal and that everyone else gets an occasional little flicker now and then?!? I was toying with the idea of bringing this one back too thinking that somehting may be wrong with the shipment my GC got in... but this is somewhat normal and something I should not worry about?!?

chris

Re: Fantom X Color LCD

27 Apr 2004, 01:02
To really know what's normal or not we would have to have our FX's next to each other. Well, I suppose that ain't gonna happen so:

Try your FX in a different locations running the power cord from a different outlet (from a different group!) and see if the problem remains. Have you checked the quality of your house electrical power system? Is the voltage constant? Any large power users (fridge, oven) connected to the same group?

Do you have any fluorescent (neon) light in your basement? Try turning it of an use incandescent light (plain old lightbulbs, not the power saving ones). The interaction of the backlight CFT and external neon light may be causing problems. They are both flickering at 50/60Hz which you normally don't see that much but if they interfere that could be a different story.

If possible try running your FX from a UPS (Uninterruptible Power Suppy) running off the UPS' battery. This will guarantee a constance voltage to your FX. See if this makes any difference.
http://www.youtube.com/watch?v=TXz0UkVBZPQ
TOYZ in 60 seconds (short live video of my progrock band on YouTube)

Re: Fantom X Color LCD

27 Apr 2004, 07:44
my studio is pretty controlled as I am a video editor, so no flourescents and yes, everything of value is being run off of UPS's. I went out and purchased the X6 its very own UPS before I even got it home. I have tried the different outlet/different section option too and same thing. The fluctuation is not all the noticeable but it just scares me as my first X6 definitely had display problems... and after seeing this one flucuate a little I am wondering if its an early sign of failure. I know, the best way would be to sit them side by side like you suggested but that aint gonna happen liek you said. I am going to go check the one on display back at my GC and see what is going on there so I can compare them.

When you said a little flickering is normal, I think that is the category I fall into if in fact that is the case.

thanks for the reply,

Chris


thanks for the reply!

Re: Fantom X Color LCD

30 Apr 2004, 11:31
This is documented (sort of) in the documentation which came with the X. It advises that the screen may need time to initialize to it's full brightness. Once it "warms up" (usually less than 10 minutes) it should stay steady.

Regarding the overall dim-ness of the display...what I have noticed is that the viewing angle of the F-X screen is very narrow in comparison to the F-S screen. There is about a 45 degree angle which you can look at the X screen and get it's best and brightest view, regardless of the contrast knob setting. And this 45 degree angle is very "high" over the board. You need to be sitting up (or standing) looking down over the board to comfortably be within this viewing angle. If you sit in front of your X, looking forward at it, you will likely be tettering on the edge of being outside this angle, where the brightness diminishes greatly.

You'll notice that the screen has been angled upward in the construction of the X, unlike the construction of the S where it is flat. This is not just a cosmetic or convenience feature. This is necessary to give you "any chance" of being in it's optimal viewing angle while sitting in front of the keyboard. Overall...this is less than optimal in my opinion. The S had much better viewing angle, and much better contrast control. Albiet, with grayscale graphics that are harder to interperet.

Pretty much any where I would sit in front of my X, I would find myself needing to lean forward uncomfortably to work with the screen. My ultimate solution was to place the X on an angled keyboad tier stand (at about a 45 degree angle, so with the screen already being angled, it is facing me directly), and now the X faces me dead on when I sit in front of it. I actually like this quite a lot not only for the best screen viewing, but for the ergonimics of editing and working with the board. But frankly, I found it almost unbearable when I had it sitting flat.

Thanks,

Ron

Re: Fantom X Color LCD

2 May 2004, 04:15
Not sure if my problem is related, but mine flickered a bit here and there until I plugged the unit into a power conditioner. A computer UPS can be tried if you don't have a conditioner because they usually include a power conditioner.

X8user
X8user

Re: Fantom X Color LCD

2 May 2004, 09:27
I am going to try that next, I use a conditioner for some of my editing gear so I have one, I just need to run an ext. cord to reach it.

thanks

Chris

Re: Fantom X Color LCD

5 May 2004, 00:33
I used to have this really cool wooden stand that set my Prophet 5 at an angle on my Rhodes. That sounds perfect for getting the X at the right angle.

← Back to Fantom-S and Fantom-X