V-Synth

How to write MIDI messages from V-synth?

How to write MIDI messages from V-synth?

22 Nov 2006, 20:11
I would like to write MIDI notes and controller from V-synth XT
to my sequencer (Sonar).

For example, found good arpeggio and want to change a couple of notes in it. I was not be able to do it through USB.

Also I wanted to write my manipulation with Time trip Pad.

Could not realise how to do it.

Re: How to write MIDI messages from V-synth?

22 Nov 2006, 21:47
The arpeggiator patterns for a patch are accessible via system exclusive.. I don't know if anyone has written an arpeggiator editor program. But it could be done I think? The info is in the back of the manual. One would have to be a real sysex-freak to do it though :-)

Error 144 - Reboot y/n?
Error 144 - Reboot? Y/N

Re: How to write MIDI messages from V-synth?

23 Nov 2006, 03:12
Keyboard and TTP send usual MIDI note and controller messages, and knobs send SysEx messages. These can be recorded in any MIDI sequencer if you plug XT's MIDI out (whether real or USB MIDI) into the it.

As about the arp, the built-in editor is more than enough as to me. Just go to the Common tab of the patch view, and locate the button named Pattern Editor or something like that.

Re: How to write MIDI messages from V-synth?

23 Nov 2006, 13:32
Thank you, Artemio for your answer.

But I usually thoroughly read the manual before ask something. I red that "USB MIDI driver ...passes data from V_S XT to the application". How? That particulary do I have to do via USB? I could not managed it. It seems to me that USB -is only for storage - for example you can not use the arpeggio via USB.

About writing arpeggio - sorry for my wrong explanation. I need to write an arpeggio from V-synth to my sequencer - 16 chords, about 1 min time and change 2-3 notes from that 1 min sequence - about 8 notes X 16 chords = 128 notes. I need to change 2-3 notes from 128 notes, I know how to use Pattern Editor. For example, It was very easy for me to write
arpeggio from Yamaha motif rack. Honestly I do not have second MIDI cable so I forced use USB.

Re: How to write MIDI messages from V-synth?

23 Nov 2006, 14:47
1. To get it work via USB:

- Install the USB driver
- Go to [MODE] -> System and find the USB settings, set USB mode to MIDI
- Now connect to your computer
- You should be able to select V-Synth XT as a MIDI in and out in any host application

2. I am not sure how to do this if it doesn't just work via MIDI, I never tried this. Maybe someone else can jump in to answer.

Re: How to write MIDI messages from V-synth?

23 Nov 2006, 17:56
Yes! It is working. Artemio, you were right - driver was installed incorrectly.

You should set it [Mode] - [System]-[MIDI USB] - clock source - -MIDI or USB MIDI and [USB-MIDI thru Sw] -switch ON. Now I can write midi data from V-synth XT to Sonar,

but without arpeggio - sorry, this is Roland. Tomorrow I am going to buy second midi cable and try to write an arpeggio via midi.

thank you anyway!

Re: How to write MIDI messages from V-synth?

6 Dec 2006, 10:59
It turned out very difficult to write midi from V-synth to Sonar!

I use just MIDI cables, without USB. I tried to do this for 2 hours without success.

Eventually I have only controllers through TT pad, no notes.

When Sonar plays notes through V-synth it do not recognise any midi events going to Sonar, just from - you have special thumbnail with indicators in the bottom of your comp. monitor. If Sonar sees midi event which go inside it indicator is blinking red. When I tought TT pad - I have red light and Sonar records but only controllers, without notes.

So I think problem is not inside Sonar.

Can anyone prompt me?

Re: How to write MIDI messages from V-synth?

9 Dec 2006, 17:45
the v-synth can't send midi note events like, say, the virus can... there's no arpeggiator send option.

← Back to V-Synth