FA-06 / FA-07 / FA-08

New FA07 User: I have a question.

New FA07 User: I have a question.

6 Jul 2018, 08:09
Hi everybody!
I'm a new FA07 user, my wife bought me one as a Birthday Present (yes, Lucky Man I am) and I'm really enjoying it so far.
Coming from a Roland Juno G, I really enjoyed both the possibility to load the old SRX boards (I had the SRX07 and so EXP02 is already loaded in my Slot 1) and to have all those old JV and XV sounds in there :)

However, I have a question which is bugging me and even if I read many posts, I prefer to ask it here, since I could have misunderstood some replies in other posts. I also had some discussions with Italian users and two of them stated that it's possible to do a certain thing, while I couldn't find a way to do it.

This thing is: saving some kind of reverb information on a User Tone. To me, it's impossible, since (Ref. Manual, page 52, the Reverb Settings are STUDIO SET settings, and not TONE Settings).

So far I learnt that (please confirm):
  • MFX settings are stored with the Tone.
    Reverb, Chorus, IFX, TFX, Compressor, etc. are saved with the Studio Set.
So, if I want, let's say, a "reverberated" version of 011 West Coast, all I can do is to create a new Studio Set with that Tone on Part 1, adjusting the Reverb Settings as I like, and then save this Studio Set, instead of a new version of the Tone. Is it right? The Reverb information is NOT associated to the single Tone, but with the Studio Set I put this Tone in.

This also means, correct me if I'm wrong, that every tone sounds different depending on the Studio Set you put it in!

Please clarify this aspects, because I'm becoming mad at figuring out how it is possible for a Tone to have its own Reverb settings, no matter what the Studio Set settings are.

Re: New FA07 User: I have a question.

6 Jul 2018, 09:13
Yes you are correct, the 3x (?) MFX's on the Juno G were spread across all 16 parts, whereas the FA has 16x MFX's in total, but cannot be stacked - i.e. 1 MFX per Part (Tone).

So, what that means is that you can't stack a phaser and reverb MFX into the tone itself.

Most reverbs therefore rely on the global reverb level, as you've correctly discovered is set by the studio set in use. However you can change the send level of each part so you can add as much or as little of that reverb as you wish for each part. - From memory the Juno G was also structured in this way also, unless you were using MFX for reverbs?

I much prefer this way of MFX usage as it means that any tone i create will sound the same once i bring it into a studio set - the Juno G, at times, you would find a great tone but when putting it into a set would become very thin - particuarly if it required multiple MFX's that are no longer available as another part is using them.

In practise, it's very easy and quick to get to your reverb for each part, in the Sound Matrix section of the front panel the bottom row (As labelled) is the overall Reverb/Chorus setting (Knob 3+4), and then for the part you are focused on the, with the third row enabled, Assign 5 and Assign 6 (numbered) knobs on the sound modify matrix are the individual Chorus and Reverb levels for the part.

You can also hold the shift button down and turn the global chorus or reverb knobs to get directly to your chorus and reverb settings too. So knowing those quick shortcuts, for me personally of course, negates the need of having to set individual reverbs with each tone.

The Studio Set, of course is your environment to how those tones fit into a mix, so that's the logic of how the FA is designed to work.

You can also go into the studio set part view and change the reverb levels individually via the display if you don't like using the "Assign 6" control, or which to set it to some other action.

Re: New FA07 User: I have a question.

6 Jul 2018, 12:21
Thank you very much for your kind reply :)

You're right about the 3MFXs in the Juno, having one per Part in the FA is a big improvement. However, what I miss the most is a "real" Patch (Single) Mode. In that case, each Patch had its own Reverb and Chorus settings, besides its MFX. Here, instead, even when we are in Single mode, we're like we're in the old Performance Mode :)

That said, it's only a matter of updating my way of thinking. In any case, arranging sounds in the Studio Set is very easy and the display is a real pleasure to look at :)

I just disagree a bit on this sentence of your post:

I much prefer this way of MFX usage as it means that any tone i create will sound the same once i bring it into a studio set - the Juno G, at times, you would find a great tone but when putting it into a set would become very thin - particuarly if it required multiple MFX's that are no longer available as another part is using them.

While it's undoubtely true what you said about the JUNO and the patches sounding dull in Performance mode compared to the shiny versions of Patch mode, I disagree when you say that any tone will sound the same once you bring it into a studio set. To my understanding, if two studio sets have different options regarding IFX, Chorus and Reverb, the same tone will sound different, won't it??

Re: New FA07 User: I have a question.

7 Jul 2018, 05:48
RobyKeys682 wrote:
While it's undoubtely true what you said about the JUNO and the patches sounding dull in Performance mode compared to the shiny versions of Patch mode, I disagree when you say that any tone will sound the same once you bring it into a studio set. To my understanding, if two studio sets have different options regarding IFX, Chorus and Reverb, the same tone will sound different, won't it??
Well, my studio sets aren't vastly different in terms of the reverb and chorus settings - i always start with a init studio set and the most i will change is the Chorus to a delay, and then change the send level on each part as suits the song (Using Assign 5/6 as said previously). So for me personally i find the patches transfer across studio sets fine, and to be more specific perhaps i should've said 'near' the same.. :)

That's not to say you won't hear larger differences of course, as it's so subjective - i.e. you may prefer huge plate reverbs on pianos etc which makes much of the sound, but you'll find over time the workflow is so quick you can change all that on the fly with minimum fuss. What sounds good by ear is key to me, and being able to tweak that in seconds makes it just not a concern.

So, The point i was making is that no more do will you load an Organ, for example, and realise you can't even hear the amp or rotary effect as there's no MFX slots. For Roland to make that work means that 16 parts = 16 MFX's, so you cannot stack MFX's, i guess that's purely down to the available power of the DSP chip. And for me personally i prefer this approach.

You are probably studying everything in depth as you're new to the keyboard, but you'll realise in time how much better the workflow is vs Juno G, and how effortless it is to browse and bring in new patches without having to micromanage MFX's - that's such a huge advantage. Also holding shift for knobs such as the reverb and chorus controls gets you straight into adjusting them - they're massive workflow savers.

To start with i was thinking that one MFX per tone is going to be limiting too, but it's not, not in use. Particularly when you see how easy it is to layer sounds. Having the individual sends for each part going to Reverb and Chorus (Which you can use as a delay too) can be used really creatively.

Once you start using TFX/IFX for an additional effects bus then yes, the sounds at that point can differ dramatically from their root sounds. But that's kinda the point. :)

I usually keep compression and EQ's to neutral in their studio sets too, but then i'm using the FA to mix down into a DAW.

Re: New FA07 User: I have a question.

7 Jul 2018, 06:37
Hi, and thank you again for replying! :) Sorry if I sounded pedantic, but I wanted to be sure to have understood well the concepts at the base of the FA O.S. :)
That said, I agree with all you said, I'm studying and experimenting with the various screens, knobs, functions... Of course, having 1 MFX per part is a great improvement compared to the JUNO G architecture.
I'm laying down some "template" studio sets with different settings for Chorus and Reverb, and then I'll recreate some of the old Performances I had on my Juno (which, BTW, I still love and plan to use in live gigs :) ).
At the same time, I'm going to go through all the EXPansions and note down the sounds I like best on each of them for quick future recalls, since I think EXP2 and EXP5/EXP10 will stay loaded the most of the time.
I'm having lots of fun in doing this! :D
And I still to have a look at the SN Synth Engine :D

Re: New FA07 User: I have a question.

7 Jul 2018, 12:49
RobyKeys682 wrote:
Hi everybody!

So, if I want, let's say, a "reverberated" version of 011 West Coast, all I can do is to create a new Studio Set with that Tone on Part 1, adjusting the Reverb Settings as I like, and then save this Studio Set, instead of a new version of the Tone. Is it right? The Reverb information is NOT associated to the single Tone, but with the Studio Set I put this Tone in.
Yes and no :-)

I'm going to go through steps to help you see how this is all set up and hopefully make it easier to use for yourself.

There are really 3 places for effects, PLUS, 1 more for Chorus!

Do the following:

1. Go to an empty "INIT STUDIO" slot. It's probably by default in "Single" view with 0001 Full Grand as the Tone on Part 1.

2. Press and hold Shift then press Effects Edit (Button 3 under the screen) and it will take you to the FX screen.

3. Now, notice that Part 1 has an Equalizer on it. This is the MFX that is stored with the tone.

4. Notice there is a Reverb option at the bottom. Press its button (4) and it will bring up a screen. Should be "Room 1".

5. On the knob matrix, move the arrow to the last row and move the knob for Reverb and watch the screen. You will see the values for Time and Spread change! (notice also here you can assign this to Main or Sub).

Now, I've been trying to figure out Roland's logic here (good luck) and compare this to a typical mixing console.

Here's what I've discovered:

6. Every Part in the FA is like a Channel Strip in a Mixer. And that mixer has a Reverb Box on Aux 1, and a Chorus Box on Aux 2. Each and every TONE has an amount of Chorus and Reverb send associated with it.

7. So, press the MFX button and it will bring up a screen that has the Equalizer (from #3 above). If you scroll down to the bottom you will see Chorus and Reverb Send levels of 127. Even if you set the type of effect to "Thru" you'll see the Chorus and Reverb Send (still set to 127).

It seems that all the patches have values of 127. This means, it's like the Aux 1 send knob on your mixer is maxed out on every single channel, all the time!

But, if you look at the main FX screen there's a "send" which is really more like an Aux send - by default it's "20" to Reverb and "0" to Chorus.

This seems very redundant to me but if the level in the MFX is 0 for Reverb, it won't matter if the one in the FX screen is set to 127 or vice versa. Now, this might be how much of the EFFECT itself is being sent to the reverb but it seems to be the only way to make sure the Tone itself will get sent to the Reverb "Aux" as well when you use "Thru". (they are also unaffected by the MFX switch).

So all of that is ONE place for Reverb. The TONE's "send level" has to be up, AND the value in the FX screen, 20 by defualt, has to be up as well.

As you suspect, if you change the value on the TONE side, it has to be saved with the tone, but any time you recall that tone you will get that setting with it.

The "20" though is saved with the Studio Set.

So you could theoretically do this - you could put Full Grand on Part 1, and Full Grand on Part 2. Those have the same default everything, so they'll both "send" 127 to the Reverb. But within the SS, you can change Part 2 to 127.

Now, when you turn up the knob in the Matrix, it's changing the time and spread for ALL 16 Parts, but Part 2 in this example is going to be affected more because it is sending more to the "Aux Reverb".

I want to think that the Matix knob works like an "Aux Return" but really it doesn't - it's like changing values on an old school outboard reverb box - you have Time and Spread, and when you turn the knob all the way down, Bypass.

Now, the next place to get Reverb is the TFX. It affects all 16 parts. So in that way, it's like a "Master Insert" effect. And it is saved with the Studio Set.

THE BIG DIFFERENCE IS - you can CONTROL the TFX in real time. You can control some parameters of the MFX in real time by a convoluted assigning system, but, for example, you can't just simply turn the effect on and off!

If you wanted Tremolo on an Electric Piano, and just wanted to turn it on and off, you can't do that with an MFX.

It HAS TO BE TFX!!!!!!

Let's say you want a Bass on the lower half of the keyboard, and EP on the upper half, and you need to change from the straight EP to an EP with, let's say Delay on it for whatever reason.

There's no way to do this simply in the FA becuase you can't turn the MFX on and off.

Instead, what you need to do is create a tone with the Delay on, put it in Part 3, and then switch between Parts 2 and 3 (or whatever your upper half sounds are on) to get the non effected and effected versions of the SAME SOUND!!!!

Stupid. But I digress.

You can also use IFX for Reverb, and it works just like an "insert" effect on a mixer, where ONLY that 1 part is effected. This too is saved with the SS, but, it's the same for all of the Parts - you can only have 1 IFX type on at any time and all settings are shared across all Parts. The only thing you can do is select which parts are being sent to it.

It has its own Reverb and Chorus send levels (which just makes this all the more confusing!).

But, I guess the logic here is, if you want Reverb on a sound, and Delay, but you don't want the Delay to have Reverb on it, you set the FX screen level to 127 for verb, and 0 coming out of the IFX Delay. Conversely, if you want The Delay to have verb on all of the repeats, you'd do the opposite. Have tried this and it works.

So IFX is the THIRD place you can get Reverb but is more involved and specific.
This also means, correct me if I'm wrong, that every tone sounds different depending on the Studio Set you put it in!
No, not really. If the effect was stored with the TONE as MFX, then it's always going to be the same - that is, assuming you're calling it up into an INIT STUDIO patch.

Of course, if you call up a tone into a SS that has TFX turned on and it's some kind of mad filter, then yes, your sound is going to go through that Filter, but I think you understand that.

Please clarify this aspects, because I'm becoming mad at figuring out how it is possible for a Tone to have its own Reverb settings, no matter what the Studio Set settings are.
The only "reverb settings" any Tone has is what levels are set in the MFX "Reverb Send Level" settings. And those are stored with the Tone. And since by default they all seem to be 127 it's kind of a moot point.

Here's where it makes a difference: Let's say you're going to create a Supernatural Synth tone from scratch and you use an "INIT TONE" for this. Well, IIRC, the default MFX for those have C/R send levels of ZERO! I spent a while trying to figure out why neither the FX Screen Reverb Level or the Knob wouldn't add Reverb to the sound. I'm like "it's sending, and the amount is up, why won't it work". Well because this "redundant send level" in the tone itself was set to 0. Turned that to 127 and it worked like all other Presets!

So let's recap:

1. MFX are stored with the Tone and follow that tone into whatever SS you place it in.

2. TFX are stored with the SS and affect ALL parts in the SS.

3. The Reverb and Chorus levels, as well as the Matrix Knob values for those effects are stored with the SS as well. They also affect ALL parts in the SS BUT you can control how much of each single Part's signal is sent to the C/R and save that with the SS.

4. IFX is also stored with the SS and affect all parts it is turned "on" on with the switch.

Re: New FA07 User: I have a question.

7 Jul 2018, 13:21
RobyKeys682 wrote:

You're right about the 3MFXs in the Juno, having one per Part in the FA is a big improvement. However, what I miss the most is a "real" Patch (Single) Mode. In that case, each Patch had its own Reverb and Chorus settings, besides its MFX. Here, instead, even when we are in Single mode, we're like we're in the old Performance Mode :)

That said, it's only a matter of updating my way of thinking. In any case, arranging sounds in the Studio Set is very easy and the display is a real pleasure to look at :)
Just in case you don't understand this:

The "performance modes" of the FA are really just one mode - 16 Part Multi-Timbral.

What changes is "what you see". IOW, it's always in 16 part mode, and all 16 parts are available. But, pressing the "mode" buttons really just change the VIEW. I like to think of them as a "filter" for views is all.

So "Single" mode just shows you Part 1 on the screen.

"Dual" and "Split" modes just show you Parts 1 and 2 on the screen.

Then "Studio Set" mode shows you all 16 (or however many fit).

But really, you're always using a SS, and you're always using 16 Parts, you're jut not playing them all and in some cases, filtering the view so you don't have to look at all the ones you're not using!

So when you are in "Single" mode, you have the MFX that is stored with the tone, and the Chorus and Reverb send levels or Part 1, and the TFX (which could be Reverb) and if you like, the IFX (which could also be Reverb).

But it's EXACTLY like it was Part 1 of a SS - it IS Part 1 of the SS! You're just seeing only Part 1 on screen!


So here's the catch:

I'm playing in a band, and I need Piano, Organ, Clav, EP, Strings, Brass, Synth etc.

I can set ALL of those sounds up in 1 Studio Set. They will all have any MFX associated with each Tone, and I can add additional C/R for each Part via the Matrix Knobs (or store it with the set) and put an effect on the entire thing (TFX) if I want.

So for me, it's way easier to call up a single SS and use the Pads to switch between sounds - pad 1 is the Piano, pad 2 is Organ, and so on.

Live, on stage, it's much easier to jump between sounds this way. You can do this with the "favorites" button but you're limited to 10, without having to press the Bank button. You can use the Pads now to reach Favorites but it's just as easy to set up the Keyboard groups.

And where this becomes important is, let's say, I get to a gig, and the room is just super soaky reverby and I'm like, oh crap, there's just no need for me to have reverb on the instrument now - so I can just turn down the TFX and ALL my sounds will decrease by the same amount.

If I had saved them as individual patches (multiple studio sets with Piano on Part 1 on one, and Piano on Part 2 on another, etc.) then I'd have to go in and change each one individually. What a nightmare!

Another example is, the genuises at Roland gave you no way to turn the MFX on and off and real time, and there's like not a single sound that doesn't have SOME kind of MFX on it - I mean, it's on everything all the time but I think it's pretty rare to find a patch where the MFX is set to "Thru" or with values that don't cause anything.

So let's say you have some synth sound you're going to use for a song for pads, and are then going to play a melody on that pad sound with delay on it for a solo, and then want to use a different synth sound on the lower half of the keyboard for bass.

Well, you can't do it unless you have an effected and a non-effected version of the Pad tone saved. And you won't. Because they didn't do that.

So what you have to do is have your Preset Tone, "Pad with Delay", and then edit it, turn the MFX off, and then Save that as a new USER TONE.

Now you have to set up your SS with, say, the Bass on Part 1, the Pad on Part 2, and then the Pad with Delay on Part 3.

Now you have to figure out a way to play Part 1 on the lower half of the Keyboard, and Parts 2 and 3 on the upper half, but be able to switch between Parts 2 and 3.

The only answer is to use Keyboard Groups and switch between them within the same SS.

Oh, you could make TWO SS , one with the Pad no delay upper, and one with the Pad w/Delay upper, but if you make any changes to anything, and then switch SS, it's going to negate those changes. So let's say you're playing and you realize it's just too dry so you turn up the Reverb you have set to the upper part. Then you switch SS to get to the Delayed version. Fine, maybe it doesn't need the extra Verb because it's got the delay.

But what happens when you switch the SS set back to the former one - that amount of Reverb you set would have to be set again!

So doing it all within the same SS alleviates this problem (of course for either example, you'd have to ultimately store the changes if you wanted to keep them).

Now, of course, changing SS can actually be a GOOD thing if you need to "wipe out" a bunch of changes you've made during a performance.

So yeah, it just takes a little getting used to to figure out what's going to work best for you. I just pretty much work in SS mode all the time - even if I'm using just a single sound, because I see the "modes" really as just "filtered views" and figure I can use 16 sounds in one memory slot versus using up 16 SS memory slots instead!

But if I have to have something with a specialty setup, yeah, it has to go on its own studio set.

Re: New FA07 User: I have a question.

8 Jul 2018, 02:01
Steve, thank you very very much!! I appreciate the time you spend in replying to our questions!! For now, I only read your answers, but today I'm going to follow step by step and then reply with my thoughts! :)

Re: New FA07 User: I have a question.

8 Jul 2018, 02:50
OK, while wife is still sleeping, I turned the FA on and performed the steps you listed, and everything is now clear to me (the fact that Single and Dual modes are just filtered views of the SS was already clear to me, but thank you for highlighting it, anyway! :) ).

IFX sounds like a good idea in some cases, since it's easy to tell the FA which parts must be affected by it or not.
I mainly play pop / pop-rock, so my SS won't be very complicated (max 4-5 sounds per SS), but I'm starting to like the many ways I can layer and setup things. BTW, one crucial point which made me opt for the FA was the Keyboard Switch Group function, very powerful and useful for live situations!

I only have one more question:
stevel wrote:
The only "reverb settings" any Tone has is what levels are set in the MFX "Reverb Send Level" settings. And those are stored with the Tone. And since by default they all seem to be 127 it's kind of a moot point.
What about the Chorus and Reverb Send Level parameters for each of the four partials in PCM tones?


Edit: Steve, I found a patch which has 0 for Chorus and Reverb Send Levels :D It's an old favourite of mine, PRS 207 - You and Luck! :) This patch has Space-D as MFX, which is, to my ears, very similar to a Reverb... :D

Re: New FA07 User: I have a question.

9 Jul 2018, 12:28
Steve, just to tell you that after your in-depth explanation I was able to quickly create many Studio Sets for 20-25 songs I play with my best friend (guitar and harmonica). I was impressed by how easy is to set-up things after you learn the basics, and btw, I LOVE the Keyboard Switch Groups :)

Re: New FA07 User: I have a question.

13 Jul 2018, 22:55
RobyKeys682 wrote:
Steve, just to tell you that after your in-depth explanation I was able to quickly create many Studio Sets for 20-25 songs I play with my best friend (guitar and harmonica). I was impressed by how easy is to set-up things after you learn the basics, and btw, I LOVE the Keyboard Switch Groups :)
Yes the Keyboard Groups was a godsend!

Honestly, I hadn't dug very far into the PCM sounds at all and I know the architecture is a bit different. I was still trying to just figure out the basic stupid structure when I figured out as much as I did with what we have so far!!!

I actually do really find the options great - I just responded to another poster about the "old" way of doing it which actually would work for what they wanted - but you have to NOT uses a KSG - so it's nice that they kept the legacy method.

My two biggest complaints about the FA 06 are:

1. You can't control MFX in real time - I just want to be able to turn it on and off. All those stupid SN-S sounds with goofy delays on them - I just want to turn it off and save the sound in that state without having to save it in a user slot. I just think that was absolutely stupid.

2. The keybed of the 06 is pretty bad IMHO. "shaved" keys (dimensions are slightly smaller than standard) and it's WAY too easy to accidentally "brush" a neighboring key and it will play. Also, it's WAY too easy to trigger 127 velocity. Especially on the black keys. I have an A-800 that has the similar keys but you can pound it hard as you can and it won't reach 127 velocity. It also has WAY better velocity curves. Roland actually snuck in some additional Velocity Curves with the update so you can control the VC of each part indpendently - but there's still no way to keep it topping off by barely pressing the keys - even at the highest setting in the main part and the VC that has the bet curve, you can still easily hit 127 velocity. That too is just goofy. I really want to try an 07 to see if those things are better.

Re: New FA07 User: I have a question.

14 Jul 2018, 04:57
Yes the Keyboard Groups was a godsend!

Honestly, I hadn't dug very far into the PCM sounds at all and I know the architecture is a bit different. I was still trying to just figure out the basic stupid structure when I figured out as much as I did with what we have so far!!!
The PCM sounds may be easily overlooked, IMO... I actually was able to recreate some favorites of mine which I had in the Juno, as well as some sounds like a typical L.A. Piano. And you know what? I prefer these sounds to the default SN sounds.
My two biggest complaints about the FA 06 are:

1. You can't control MFX in real time - I just want to be able to turn it on and off. All those stupid SN-S sounds with goofy delays on them - I just want to turn it off and save the sound in that state without having to save it in a user slot. I just think that was absolutely stupid.
I totally agree!
2. The keybed of the 06 is pretty bad IMHO. "shaved" keys (dimensions are slightly smaller than standard) and it's WAY too easy to accidentally "brush" a neighboring key and it will play. Also, it's WAY too easy to trigger 127 velocity. Especially on the black keys. I have an A-800 that has the similar keys but you can pound it hard as you can and it won't reach 127 velocity. It also has WAY better velocity curves. Roland actually snuck in some additional Velocity Curves with the update so you can control the VC of each part indpendently - but there's still no way to keep it topping off by barely pressing the keys - even at the highest setting in the main part and the VC that has the bet curve, you can still easily hit 127 velocity. That too is just goofy. I really want to try an 07 to see if those things are better.
I chose the FA07 because of the bad keybed of the FA06. Which basically was the main problem on the JUNO G, too. So, the FA07 sounded like the obvious choice for me in terms of keybed and weight :)

Re: New FA07 User: I have a question.

14 Jul 2018, 06:05
Another question, Steve:
I was playing with some SN sounds. Let's take for example '68 Reed.
If I push the modulation lever up, a sort of tremolo is applied.
So, I went to the MFX and MFX control page, but I couldn't find any sign that CC1 effectively is assigned to activate the tremolo. Moreover, if I disable the MFX, the modulation lever continues to apply the tremolo, if pushed.
So, my question is: where is it written that the MOD Lever applies that effect? I looked everywhere, both in Tone Edit screens and in Studio Set common, but I couldn't find an answer.

Edit: I find an old topic in which you explained that by default this is due to Control Tone 1-2-3-4, which by default are set to Modulation and other parameters... I followed your example with the first SN Strings patch and changing Control Tone 1 from CC1 to CC3 sort of disabled the Mod Lever. What I still don't understand is why, for example in the first SN Strings patch, the Mod Lever increases the volume.

Re: New FA07 User: I have a question.

16 Jul 2018, 20:33
RobyKeys682 wrote:
Another question, Steve:
I was playing with some SN sounds. Let's take for example '68 Reed.
If I push the modulation lever up, a sort of tremolo is applied.
So, I went to the MFX and MFX control page, but I couldn't find any sign that CC1 effectively is assigned to activate the tremolo. Moreover, if I disable the MFX, the modulation lever continues to apply the tremolo, if pushed.
So, my question is: where is it written that the MOD Lever applies that effect? I looked everywhere, both in Tone Edit screens and in Studio Set common, but I couldn't find an answer.
On Pages 118 and 119 of one of the manuals (sorry not sure, but it's like the parameters one I think) are listed the "SuperNATURAL Tone CC Assign". (note, if you're looking through manuals, keep the wrong one if you hit it first because there's another useful chart on pages 118 and 119 in another manual I refer to below!)

If you look at 68 Pure Reed, you'll see the tone is made up of the SN-A sound "Pure Wurly".

This tells you C16 does "noise level" and CC1 does "Vibrato". There's an asterisk on the column for CC1 which has to do with "System Control" which I don't fully understand.
Edit: I find an old topic in which you explained that by default this is due to Control Tone 1-2-3-4, which by default are set to Modulation and other parameters... I followed your example with the first SN Strings patch and changing Control Tone 1 from CC1 to CC3 sort of disabled the Mod Lever. What I still don't understand is why, for example in the first SN Strings patch, the Mod Lever increases the volume.
So look on those pages at the String sounds and you'll see CC1 controls "dynamics+vib" - so that's the volume increase you're hearing.

So basically, what Roland has done is "built in" these CC controls to various sounds that you really can't edit or change TMK.

This comes from all the people using DAWs with Orchestral Library plug ins that have similar features.

In the old days, we would have to change PATCHES to get Pizzicato - you had one patch for bowed strings and you picked another for Pizz.

But since the modern plug ins are based on sampling, you can "include" a different sound with a CC# in much the same way we could use aftertouch or velocity to trigger different sounds in a PCM patch.

I found another page in the manual (not sure which again, sorry) that has "Performance Variation Sounds" (p. 29 of wherever it came from).

It lists "Variation" 1, 2, 3, and 4 which has something to do with this as well, but I've not gotten that far into it yet. You can see the strings have the same options. Again these must be "built in" to the sound itself.

If you look at pages 118 and 119 in the "MIDI Implementation Chart, you'll see that CC80-83 are "Tone Variation" and CC16+ is "Tone Modify".

So these things are "built into" the sound.

What Roland has done is to use some "empty" CC numbers that have been designated "General Purpose" and written specific things into the sound that will be affected by those numbers.

A long time ago, CC91 and 93 were not designated as Reverb and Chorus but Roland started using them that way consistently until GM2 came out (or it might have been the GS extension) where they are no considered the default for those numbers (like how 7 is volume). So they're sort of doing the same thing here.

You'll notice that there's a set of numbers marked "General Purpose Controller" and that's mostly the ones that aren't already being used for other parameters - these are "empty" CC numbers "held" for customizable use.

I think what we have in the FA is the ability to "re-designate" certain numbers to they can be changed along the way for whatever reason (like you've got some other synth that uses that number and don't want them to get confused or something). It also probably gives you a way to create tones that responde to different numbers - for example, on an MFX, you could assign "speed" in any effect with it to CC20 and assign that to the first knob in the Matrix so that knob is always speed on any effect you call up. But on another tone, you might have just a one off parameter that you want to assign and you'll need a different number for that one.

Again I haven't gotten that far into it but that's my take on it so far. It's probably really really powerful if we actually got into it!

One final thought - Pitch Bend has always been considered it's own category and doesn't show up in CC lists.

Modulation is somewhat similar in that it was around before the GM standard - which is probably why it got #1. But I believe the understanding is that a "mod wheel" should apply modulation, period. Whether the sound could do it in real life or not. So the default state is always "vibrato", just like the default state of pitch bend is typically up/down a step. Patches can be made that don't do this, and you can go in and edit it, but this is the general accepted standard.

Re: New FA07 User: I have a question.

19 Jul 2018, 03:40
Hi, I am new FA06 user as well. I noticed that if I am changing parameters with real time knobs for some tone, they (parameters) remains changed if I switch to another tone or even studio set. They "comes back" only after restarting my FA (switching off/on). Is it OK or I am doing something wrong?

← Back to FA-06 / FA-07 / FA-08