JUPITER-50

question about synth legends Vol1

question about synth legends Vol1

29 Jul 2013, 12:10
hi all

first off all, sorry for my bad english, it is a little bit rusty.
i have a little problem with the synth legends. install and test was no big problem. so i imported all sounds from synth legends to my JP50. before i do reinstall my backup.
after importing the synth legend i miss of lot of sound from the live-sets. Now the question - is not enough memory for complete import from Synth legends? (i had importetd registrations, live-sets and arpegios). is it possible to import only the registration sounds? It is a little hard for me to read the pdf-file for importing, because rusty english :-)

Nordi

Re: question about synth legends Vol1

29 Jul 2013, 15:21
Nordi

. . . AND . . . SO . . . You have come to what is considered by many to be THE major drawback of the Jupiter-50 (and Jupiter-80). You are correct. There is insufficient internal memory to hold all of the original factory preset sounds and the Synth Legend sounds. So, many of us decided to pick out what we liked of each sound set and load those into memory, and that is when we came face to face with the real problem. Without suitable PC-based sound librarian software, it is next to impossible to keep track of what is going on within the internal memory during the sound loading process to ensure that:

a. You load all of the tones and Livesets needed for the "new" registrations you want

while:

b. Not overwriting tones and Livesets needed for the "original" registrations you want to keep.

Since I really purchased the JP-50 for its superb Supernatural Acoustic sounds, and since I am not really into sound design, I re-installed the original sounds and just work with those. So far, I have been perfectly satisfied with that. I originally thought about adding an Integra-7, but I currently have my old JV-2080 with four SR-JV80 expansion cards in the mix, and I think that is going to give me all the sound palette I really need for some time to come. Others have worked out their own ways of dealing with this problem. Since this problem also plagues the Jupiter-80, you can find a more complete discussion of it over on that forum:

http://forums.rolandclan.com/viewtopic.php?f=44&t=46534

Welcome to the world of the Jupiter-50/80.

Good luck !

Regards,

Ted
Last edited by tnicoson on 29 Jul 2013, 15:38, edited 1 time in total.

Re: question about synth legends Vol1

29 Jul 2013, 15:33
ok, thanks indeed
i think i have a lot to test tomorrow :-)
i love the sounds of the JP and it works perfect with my nord stage, but it needs a lot of time for understanding the structure... the Nord is very much easier....

have a nice day

Re: question about synth legends Vol1

30 Jul 2013, 05:21
One problem fixed - the next problem!

Ok, had made a systemreset and load only maybe 10 Registersound new on my JP. It seems it works. But now i have another issue with midi. I send some prgrammchange from my Nord stage and it works. After some minutes i try again and it do not working anymore. Besides i tryed to edit a original Registersound, especialy the MFX, and after some minutes the JP freeze completly, so i had to restart with power switch. I had a look in the OS version and there is 1.02 I see that the latest version from August 2012 is 1.10
What do you think - will this fixed my problems or did i own a defective JP?
And, btw, it seems very strange to me, that i buy a brandnew JP50 in July 2013 with an OS older then one year?!?! (It comes directly from Roland)

Nordi

Re: question about synth legends Vol1

30 Jul 2013, 06:59
If you do a factory reset, the unit goes back to the earlier software version if it was shipped with that. It happened to me on my Jupiter 50 that I bought in November 2012, when I did a factory reset.

I wonder when your unit was manufactured? I don't know if recent units ship with 1.10 as the "factory" software, but I would hope they do so the reset doesn't cause a problem.

So reinstall the update to 1.10 and go from there. I haven't tried the Synth Legends soundset, for reasons that tnicoson mentions above, so I can't help you with that. Plus, the tones that are already on the system will keep me occupied for a long time!

--Roy

Re: question about synth legends Vol1

30 Jul 2013, 10:25
So, i had a call to Roland support, germany.
I shall send back the jp50. They say to me that hey had never heard about problems such mine (i had note-hang, i can play sometimes without to switch on any soundbank (solo, upper or percusion) and other things.

Nordi

Re: question about synth legends Vol1

1 Aug 2013, 07:36
Nordi wrote:
So, i had a call to Roland support, germany.
I shall send back the jp50. They say to me that hey had never heard about problems such mine (i had note-hang, i can play sometimes without to switch on any soundbank (solo, upper or percusion) and other things.

Nordi
Hi Nordi,
From your description it seems a MIDI created hung-up.

Do you have any problem when not driving the JP-50 from the Nord? I mean, does JP behaves normally when not MIDI connected to the Nord?

You shoul check if and what MIDI data is being sent, because that could be the cause...

What are you sending from the Nord, MIDI clock? Note Data? SysEx data?
Make Music and be Happy !!
PauloF

Re: question about synth legends Vol1

1 Aug 2013, 08:34
Hi - i found the problem and can reproduce it whenever i want.
1. create a new sound and use all three sound engines (lower, upper and solo)
2. put to the lower engine a special sound, call "Movingchr 1" (No 319)
3. the other sound engines do not need a special sound, but maybe use a fat string sound
4. play the sound. On my JP i can hear the sound from the choir with a very long delay and reverb. Very often it sounds lige a "midi-note hang on", but is is a effect on the tone.
5. now try to change the effect in the "efx-effect section"
6. when i press different buttons maybe more ten times, the JP50 freeze.
7. i can only switch the power off to wake up him again.

I found more than one sound with the same effect on the JP. I call Roland germany again and they want to have my JP back for checking this effekt.

Nordi

Re: question about synth legends Vol1

1 Aug 2013, 15:56
Nordi wrote:
Hi - i found the problem and can reproduce it whenever i want.
1. create a new sound and use all three sound engines (lower, upper and solo)
2. put to the lower engine a special sound, call "Movingchr 1" (No 319)
3. the other sound engines do not need a special sound, but maybe use a fat string sound
4. play the sound. On my JP i can hear the sound from the choir with a very long delay and reverb. Very often it sounds lige a "midi-note hang on", but is is a effect on the tone.
5. now try to change the effect in the "efx-effect section"
6. when i press different buttons maybe more ten times, the JP50 freeze.
7. i can only switch the power off to wake up him again.

I found more than one sound with the same effect on the JP. I call Roland germany again and they want to have my JP back for checking this effekt.

Nordi

That seems more a software bug than anything else.

Can any of the other JP-50 owners replicate what Nordi just explained?
That would be very useful to understand if we are in the presence of a faulty JP-50 or of a software bug
Make Music and be Happy !!
PauloF

Re: question about synth legends Vol1

1 Aug 2013, 16:07
That seems more a software bug than anything else.


Yes, i think so. Tomorrow i want to try to copy one of such tones in the upper part and try to edit the efx there. After that i will copy it back to lower part and check it again.

Re: question about synth legends Vol1

1 Aug 2013, 17:17
Nordi wrote:
That seems more a software bug than anything else.


Yes, i think so. Tomorrow i want to try to copy one of such tones in the upper part and try to edit the efx there. After that i will copy it back to lower part and check it again.


Good stuff Nordi, tell us what you got then
Make Music and be Happy !!
PauloF

Re: question about synth legends Vol1

2 Aug 2013, 03:26
Nordi

I am afraid that the folks at Roland Support might be right. I think maybe you need to send them your board. I tried the following sound set up this evening:

Lower Tone: MoVingChr 1
Upper Tone 1: Piano Strings 1
Upper Tone 2: JP8 Strings 1
Upper Tone 3: JP8 Strings 3
Upper Tone 4: JP8 Strings 1
Solo Tone: Strings

My board is running completely in standalone mode. It is not connected to anything else. Not even a PC or the iPad and it is running a restored copy of the pristine original factory sound set. I have no other sounds, LiveSets, or Registrations in memory at this time. I think you need to do the same, as PauloF suggested, and then retry your tests. Then if you are still having the problem, consider sending your board to Roland. I am very suspicious of, at least, your "hung" notes. That is usually the result of a MIDI feedback loop from some piece of MIDI connected equipment and lockups are usually the result of an incompatible or corrupt sysex command from a MIDI file or connected piece of MIDI equipment that crashes the board's operating system.

I did not split the keyboard. That is, I spread all six tones across the entire board. The mix was pretty muddy, as that is a lot of sonic activity all going at the same time, but I wanted to stress the board's processor as much as I could. I played various chord progressions for over an hour and never detected any incidences of "hung" notes. Then I went into edit and changed every parameter on all four MFX sections for each of the layers and the same for the EFXSEND sections and then played for another half hour or so. At no time did I experience any lockups of the keyboard. I even saved my "new" Registration. Powered the board off. Turned It back on. Loaded the "new" Registration. Made some additional MFX/EFX edits. Saved them, and played for another ten minutes or so and still no problem, so it looks like the problem you are experiencing is either unique to your board or coming from connected equipment or possibly from a corrupt Registration.

Good luck with this !

Regards,

Ted

Re: question about synth legends Vol1

2 Aug 2013, 05:49
Hi all
Thanks for the tips, i think i will follow you and send it back to Roland

Cu Nordi

← Back to JUPITER-50