Fantom-S and Fantom-X

Problem with external controller - midi pedals.

Problem with external controller - midi pedals.

14 Jul 2010, 23:08
Hi guys - I'm sure this CAN be done, but I'm not finding the right settings.

I want to use my Fantom X6 as my main live board, and plug a set of Elka MP-13 Midi Pedals into the X6 to trigger bass sounds, string sounds, samples, etc. , while playing other things ((chords, leads, pads, etc.) from the X6 keyboard.

I am using the X6 in Performance mode, I have the midi pedals set to Midi Chnl 2, but what happens is whatever sound I have the keyboard triggering, the pedals do the same. I've tried so many different options regarding the RX #, the check box for each sound, and the global channel, but I haven't found the right thing to work yet. I've tried setting everything I want the keyboard to play to Chnl 1 and everything the pedals should play to chnl 2, but the only sounds that trigger from either/both are whatever the 'cursar' is on at the time of the 16 performance parts.

Help?

Re: Problem with external controller - midi pedals.

15 Jul 2010, 04:21
Hi ric,

I'm struggling with something similar using 2 keyboards over MIDI. See here.

I wonder if it's got something to do with the "Remote Keyboard Switch". I'll have a play tonight & let you know if that fixes it for me.

Andy
Andy

Re: Problem with external controller - midi pedals.

15 Jul 2010, 04:21
You need to disable the Remote Keyboard Sw (Remote Keyboard Switch) which you will find under the System menu somewhere. See page 231 of the Fantom X User Manual. It's off by default but I'm pretty sure you have it enabled.
http://www.youtube.com/watch?v=TXz0UkVBZPQ
TOYZ in 60 seconds (short live video of my progrock band on YouTube)

Re: Problem with external controller - midi pedals.

15 Jul 2010, 04:27
Andy,

you most definitely do NOT want to have Remote Keyboard Sw enabled on the Fantom if you want to use it in combination with other keyboards and modules. It pretty much destroys the ability to address the 'module' part of the Fantom independently from the internal keyboard through MIDI.

The only reason to turn this on is if you MUST play (with your hands) the Fantom from another MIDI keyboard and then only if you need things like the arpeggiator to work when playing from the remote keyboard. With this on the remote keyboard will behave exactly as the built-in keyboard, ie it will duplicate the internal keyboard.
http://www.youtube.com/watch?v=TXz0UkVBZPQ
TOYZ in 60 seconds (short live video of my progrock band on YouTube)

Re: Problem with external controller - midi pedals.

15 Jul 2010, 05:23
Thanks for clarifying that, Arjan. Much clearer than:

"Set this parameter “ON” when you want to use an external MIDI keyboard instead of the Fantom-X’s keyboard. In this case, the MIDI transmit channel of the external MIDI keyboard can be set to any channel. Normally you will leave this parameter “OFF.”

Turn this “ON” when you want to control the Fantom-X from an external MIDI device when performing with the Arpeggio or RPS function"
Andy

Re: Problem with external controller - midi pedals.

15 Jul 2010, 05:44
@Arjan,

Thinking about it, I bet I have got it switched ON. Because I wanted to use my FCB1010 pedalboard to trigger RPS commands via Note values, and the Remote Keyboard Switch needs to be ON for that to work.

I'll have to re-think where I use the FCB and where I use key or pad based RPS.

Grr. Andy :o/
Andy

Re: Problem with external controller - midi pedals.

15 Jul 2010, 08:42
Hi Ricstave

I use an Elka MP-13 with a Fantom Xa with no problems, so there's no issue with your hardware combination.

So, what you need to do is keep the Elka pedals on MIDI channel 2. Then, ensure that any parts you want them to play have the keyboard switch on the Fantom turned off (i.e. the part-based keyboard switch, not the remote keyboard switch that Andy and Arjan discussed).

In the default performance setup, that would be just Part 2 - the parts are normally set to the MIDI channel of the same number. So Part 2 would receive from the Elka pedals on MIDI channel 2, and with its keyboard switch turned off, it wouldn't sound when you play the Fantom's keyboard.

The confusion may come from the fact that whatever part the cursor is on (i.e. part 1 when you select a new performance) will play the sound from the Fantom keyboard, even if you've got the keyboard switch off.

For this reason, I always have Part 1 muted to avoid this happening. Everything then works fine.

Hope this helps - post again if not and I'll see if I can help you further.
Nick

Re: Problem with external controller - midi pedals.

15 Jul 2010, 09:09
The confusion may come from the fact that whatever part the cursor is on (i.e. part 1 when you select a new performance) will play the sound from the Fantom keyboard, even if you've got the keyboard switch off.


I think ricstave is aware of this and it doesn't explain why the Fantom would play the highlighed part (where the cursor's at) when he's playing through the pedals since highlighting would only affect what you hear when playing the internal keyboard, except if you have Remote Keyboard Sw turned ON.

Maybe you are confusing the KBD switch for each part with the Remote Keyboard Sw setting in the System menu?
http://www.youtube.com/watch?v=TXz0UkVBZPQ
TOYZ in 60 seconds (short live video of my progrock band on YouTube)

Re: Problem with external controller - midi pedals.

15 Jul 2010, 19:01
Thanks for all the suggestions, guys - I will have to try finding the Remote Keyboard switch in the System Menu - that's probably what I missed. The thing that sucks is, from another thread I started about triggering longer sequences from the pedals or keyboard w/o having to hold down the key or pedal or hold pedal for the whole phrase to play w/o fading out, it seems that it's the RPS function I need to use, and if that won't work with the Remote KS off, then I've got yet another headache.....

Re: Problem with external controller - midi pedals.

18 Jul 2010, 15:14
Update - The Remote Keyboard Switch inthe System Menu/Midi was ON - I turned it off and all is working now.

Thanks!

Re: Problem with external controller - midi pedals.

22 Jul 2010, 18:30
It worked for me too (turning the remote keyboard switch OFF).

Now I have to re-assign all my RPS calls to keys on the keyboard. That should make playing some things fun! :o)

Andy
Andy

← Back to Fantom-S and Fantom-X