Fantom-G

Update 1.5 WILL NOT LOAD!!!!!! ARGHHHH

Update 1.5 WILL NOT LOAD!!!!!! ARGHHHH

28 Apr 2010, 20:52
Ok, ripping hair out now...
1. Downloaded 1.5 update, unzipped, copied the 2 .bin files to the FantomG Formatted, 8GB USB Drive
2. Did a project backup exactly like the instructions say to do
3. Verified the backup file existed and even copied it to my Mac desktop for good measure (just in case ya know)
4. Inserted USB Drive with 2 1.5 update .bin files into memory slot on back of G6
(G6 is at 1.3 Software Rev btw)
5. Power cycle the G6
6. I NEVER get that black screen that loads up the updates... it goes immediately to my "Fantom silver graphic" desktop and starts loading the internal project.

Part II
1. Do a factory reset
2. Redownload and copy the 1.5 Bin files to usb drive
3. Insert USB Drive and power cycle
4. Same as before, Fantom G splash screen and loads internal project.

HELP!!!!!!!!!

Re: Update 1.5 WILL NOT LOAD!!!!!! ARGHHHH

28 Apr 2010, 21:28
Format your USB stick, and copy the two files from the 1.5 Update folder into the USB stick. (dont copy the files to any folder inside the flahs drive)
You need a clean USB drive. Now do the rest.

Re: Update 1.5 WILL NOT LOAD!!!!!! ARGHHHH

28 Apr 2010, 22:02
yah, i remove everything out of the USB drive and just copy the 2 bin files.

works great each time, including v1.5. both my G7/G8 are updated. :p

Re: Update 1.5 WILL NOT LOAD!!!!!! ARGHHHH

29 Apr 2010, 04:40
If problem occurs during the update procedure and it doesn't start at all, then some problem must be there with your USB stick.
The USB stick must be formatted from the Fantom-G and the two .bin files have to be in the root level of the stick, not in any folder.

Also, make sure that you take a backup off your internal memory before starting anything. Then do a Factory Reset before updating and another one after updating. Then restore your internal project back in place.

If all the precautions are taken into account and still the problem persists, then you should try another USB stick. It seems that maybe the one you're working with is not 100% compatible with the Fantom-G.

Something that I've said before is that I recommend everyone to have one separate USB stick for the Fantom-G updates alone. Make sure it's 100% compatible and leave it alone in a secure place until you need to update your Fantom-G. Updating your Fantom-G using your everyday USB stick(s) can cause problems, due to the numerous write/load cycles it goes through. We wouldn't want the update procedure to stop mid-way due to a bad USB stick, would we?
This tip is not reccomended officialy by Roland, but I think that it would be nice if we took some little things like this into account as well. After all, we all know that the Fantom-G is a bit "picky" about what USB stick brand and model it works best with.

Re: Update 1.5 WILL NOT LOAD!!!!!! ARGHHHH

29 Apr 2010, 07:21
Thanks for the replies.

I have tried it with just the 2 bin files on the stick and nothing else. I have formatted the usb stick a few times now successfully... I have also used this same USB stick to save project files to and from with great success...

Is is possible that the USB stick is fine to save to but not to boot from? I mean it is an 8 GB stick, not BRAND new but maybe a year old...

It is like at boot time, the Fanton never even LOOKS at the USB drive as a boot device... I have looked all over for a setting that is something like the BIOS boot order in a PC, to tell the Fantom to look to the USB drive for boot files, but to no avail.

I also did do an internal backup of the Fantom G and saved the file off the USB stick onto my Mac for safekeeping.

Still no update runs....


I had THOUGHT that maybe I needed to be at 1.31 to run the update so I started looking for that update but it is no longer available on Roland's website so I am skeptikal that the problem is that, since I am SURE that I am no the only one that didnt run 1.31

Re: Update 1.5 WILL NOT LOAD!!!!!! ARGHHHH

29 Apr 2010, 07:30
Are you sure you put the .bin files in the root of your flash drive, not in any folder? If yes, try another USB drive.

Re: Update 1.5 WILL NOT LOAD!!!!!! ARGHHHH

29 Apr 2010, 12:37
As Artemiy says try another USB drive.

Here is a suggestion. Before you try to update the Fantom G again do a Factory reset of your current OS 1.30. Then use a USB drive that is 2GB or "smaller" in size. Use a 'Name Brand' (not generic) drive if at all possible. Format the USB drive on the Fantom G itself after doing the Factory reset. Once the USB drive has been formatted use your computer to put the Bin files onto the newly formatted USB drive. Make sure the .bin files are on the 'root' of the USB drive and NOT within the "Import" folder.

Okay... then with your Fantom G OFF put the USB drive into the FG USB slot and then power ON your Fantom G. Let us know how you make out. :)

PS: I am suspecting your current 8GB USB drive could be slightly incompatible in some ways and therefore causing the mishap in loading the new 1.50 OS.

Re: Update 1.5 WILL NOT LOAD!!!!!! ARGHHHH

17 May 2010, 16:19
Just as a follow up, I used an OLD 1GB flash drive and it worked like a champ! Successfully upgraded to 1.5 now. Thank you for the tips and help!

Re: Update 1.5 WILL NOT LOAD!!!!!! ARGHHHH

18 May 2010, 15:50
im going to do an update tonight, what usb flash drive should i stay away from?

Re: Update 1.5 WILL NOT LOAD!!!!!! ARGHHHH

18 May 2010, 17:23
Some of the memory stick problems out there maybe caused by little instant run applications on the sticks (that are not compatable with the FG. I would recommend formating a stick prior to the first time use with the FG. I am making this up, but I don't see how it could hurt to format the stick, even the new stick. I've also been told that the little apps should not hurt anything.

Just follow the instructions on page 280 of the manual.

I deticated a 1 G sandisk to the FG. I've even wrote "FG" with a magic marker on the side, keeps from putting my M3 or XS stick in the thing.

1. Format Stick
2. Backup FG to stick
3. copy backup files to computer desk top
4. Copy update files (to top level, no folder)
5. install stick in FG a boot
6. When complete remove stick, reboot FG
7. On computer I move the updater files into a newly created folder on the stick.
8. Remove stick from computer and reinstall in FG.
9. Use this same stick for routine FG Use.

I've had the same stick in use for over a year.

I name the folders for the updater by version

The stick has the project folders and a OS1.5.

I've also copied a set of SMF to the Project folder and reloaded it. I also deleted the extra samples as used in the ConnectLive Favorites.

Be sure to do a factory reset.

I then load my modified Project Folder with the content I want into the FG and save internally.

Everything works as expected.

Note: one more cooling I've done (suggested by someone else), I use a short extension USB cable (8") for the stick, I bought them online for around a $1 each, I use them on everything, this keeps me from having to fuss around trying to find the connect point for the USB port, I've even installed one one my Mac, Sure make connect sticks in and out easier.
Fantom G & X7, Motif XS6, M3, V-synth, JP8000, M1, Wavestation, Radias, Nord Lead 2X, Karma, Snow, electribes and other groove boxes.

Re: Update 1.5 WILL NOT LOAD!!!!!! ARGHHHH

18 May 2010, 17:37
Atlas is right.

USB sticks should always be formatted before your initial use. It not only clears the stick of any potentially disruptive software running in the background, but creates an 'Import' folder.

Cheers!
PiaKnowGuy
Film Score Demo
Image
PiaKnow
PiaKnowGuy
Please feel free to listen to Pirates
[img]http://www.piaknow.com/1goldpiaknowlogonew-thumbnail-thumbnail.jpg[/img]
PiaKnow

← Back to Fantom-G