Fantom-S and Fantom-X

How to switch from patch to performance through midi

How to switch from patch to performance through midi

13 Sep 2009, 15:46
Hi guys, I am building a pedal board to change the patches of my Fantom XR while I'm playing. Since I created multi layered patches using performance mode, I'd like to be able to go from Patch mode to performance mode and vice-versa while playing.

I checked the midi implementation in the manual and right now, I'm able to go through all my patches while in performance mode and to go through all my performance mode while in performance mode, but the XR does not switch from one mode to another by itself even if the correct Bank MSB , bank LSB and program change messages are sent.

Does somebody know how to do this?

Thanks

Re: How to switch from patch to performance through midi

13 Sep 2009, 16:07
I haven't tried to do this on my FantomX, but it appears that the facility may be there according to the MIDI Implementation chart. What specific bank messages are you sending? You realize that you need to send both bank MSB and LSB before each program change?

Re: How to switch from patch to performance through midi

13 Sep 2009, 16:15
For instance If I'm currently in patch mode at any given patch, I'll send:
0xB1
0x0
BANKMSB (85 for example to get USER Perf)

0xB1
0x20
BANKLSB (0 for example ti get USER PERF)

0xC1
PatchNumber(any of the 64 patch of USER perf so 0 to 63)

And it gets me into a weird mode where I get this on the FANTOM XR display:
---- 000
instead of for example:
PRST 01 Seq: Template

But when I'm already in performance mode, I get the chosen performance.
Weird hey?

Any thoughts?

Re: How to switch from patch to performance through midi

13 Sep 2009, 20:32
I assume that your roland's "Control Channel" is set to MIDI channel 16. What happens if you use channel 16 (ie, 0xBF and 0xCF, instead of 0xB1 and 0xB2)?

Re: How to switch from patch to performance through midi

14 Sep 2009, 01:44
there's a sysex-message which let's you change the sound-mode. I'm using a SonicCell but i guess, these are the same messages. just give me a minute to look it up...

you can lookup the msg in the manual from page 251 on. i did this for you (and used the fantom manual :-P ) so here it is:

0xF0 Sysex Starts
0x41 Manufacturer ID = Roland
0x10 device id (default is 17 = 0x10)
0x00 Model-ID: Fantom-XR
0x6B ------"------
0x12 Send a command
from here on: address, according to parameter address map from page 252 and on, checksum is calculated from here on
0x01 setup
0x00 ------"------
0x00
0x00 Sound-Mode
0x00 | 0x01 value (0x00=Patch-Mode, 0x01=Performance-Mode)
0x7F | 0x7E checksum (see page 269)
0xF7 | 0xF7 Stop sysex-message

i hope it works for you :)

Cheers,
Alex
gear:
Yamaha P80 stagepiano
Art X-15 Floorboard
SonicCell

Re: How to switch from patch to performance through midi

14 Sep 2009, 07:12
Avogra, I'll try it for sure and thanks for the time you took to write this! I'll let you know if it works

jg, I'll try that as well. It would be nice if it works because it is a bit simpler!

Thanks guys!
Phil

Re: How to switch from patch to performance through midi

14 Sep 2009, 07:56
that would be easier for sure. but if i remember right, i wanted to do the same on my soniccell and it didn't work. consider, that when you are in performance-mode, you might want to change the patch of a part with BS+PC. in that case, the part, listening to channel 16 cannot be assigned a new patch, instead it would change to patchmode. at least an explanation, why roland did this, IF it doesn't work.
Hmm, now my brain's a bit twisted with that many would/could/if etc. ^^
gear:
Yamaha P80 stagepiano
Art X-15 Floorboard
SonicCell

Re: How to switch from patch to performance through midi

14 Sep 2009, 13:35
Thanks to you guys, I was able to do what I want.

I had to switch from PATCH to PERFORMANCE using the SysEX tricks avogra suggested
And
I also needed to use channel 16 as jg suggested to go through my different performances.

So thanks to both of you!!
Phil

← Back to Fantom-S and Fantom-X