Fantom-S and Fantom-X

performances?

performances?

29 May 2007, 10:54
Ok i admit it,i'm a dumb ass,but i don't understand the concept of performances.Why is it necessary to use a performance,(either a preset,or user),before you make a song?Up until now i have just gone straight to mixer mode,selected the patches and fx i want to use,and recorded each track individually.I know i'm missing something HUGE here!
Oh, and once(if) this has been explained to me,how can you switch performances in a song?
Sorry,i am but a humble guitarist(if that's any excuse).

Re: performances?

29 May 2007, 11:01
Hello lampoonland,

No, that's not an excuse. . . . I'm just a humble bassist!

It is not 'necessary' to use Performances. I set up each Song on my own and this works fine. At most, I've saved a basic template with my most used instrument configuration, but that is usually tweaked.

Performances can serve as starting points for Songs or ideas for some folks. They are by no means necessary. I believe you can change Performances via Sysex commands. I record primarily in a home studio, so haven't delved into this.

Now that I think about it, is there a such thing as a humble guitarist?
;-))

Bassman
Bassman

Re: performances?

29 May 2007, 11:04
I have songs that use many different performances ...

The songs allow you to save mixer settings ... bpm changes ... and play sequencer data ... as well as having your audio tracks, too ...

I use them in a song setting when I want to change between instrument groupings (performances) very quickly (usually while an audio track is providing a sonic bridge) ...

the performances allow you to change instruments, effect settings with in a song ... for one thing, this allows you to overcome some of the effect section limitations by changing all the settings ...

You can record these performance changes into the sequencer (meaning, the song) by using the RPS function ... which admittedly, is too much to go into now in super-detail ...

I'm sure it's posted here somewhere ...

But basically, you go into PATTERN mode in the seuquencer ... select pattern 1 ... record a two measure loop ... while recording .... switch to a performance ... end recording ...

now insert that pattern (using the COPY function in the SONG EDIT, TRACK EDIT ... Copy pattern 1 into the sequencer ...

If you did it correctly ... the sequencer will now select that performance when it comes to that point in the song ...

Using this RPS technique ... you can perform alot of workarounds on the Fantom ...

Keep in mind, however, I've had my Fantom for two years and I did this for the first time about a week ago ... it was a huge breakthrough for me as RPS has kind of been my "final frontier" with the Fantom ...

Good luck ...

This probably wasn't very clear ... Just keep in mind ... one of the great things about the Fantom is that there are usually a couple different ways to get things done ...

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Roland Fantom X7, Alesis Fusion 6HD, Novation X/A-Station 25, Alesis Micron

some tunes and whatnot ...
http://www.soundclick.com/bands/pagemusic.cfm?bandID=405125
Some tunes and whatnot ...

http://www.soundclick.com/bands/page_music.cfm?bandID=405125



some tunes and whatnot ...
http://www.soundclick.com/bands/pagemusic.cfm?bandID=405125

Re: performances?

29 May 2007, 12:04
Thanks for your replies guys.Diametro,i was going to follow my original post with a follow up about recording patterns using different Performances,and looping them into a song.I think you've just expounded on my ideas about that.Thanks man!
And Bassman...indeed i am that rare breed of less erm,exuberant guitarists,not your typical wide stanced,crotch to the heavens,balls in a vice faced,fret melter,i think you might be referring to ;-)

Re: performances?

29 Jun 2007, 16:35
Hi Diametro.I tried the technique you described,but i don't quite understand the selecting a performance whilst in record mode.Do you mean select a performance in real time?I tried this,but got sound glitches,like the fantom was trying to "catch up" with the performance selection i'd made.
What performance do you start in,(what setting do you use to record the initial pattern?).I don't get how you can select a performance in record mode,ie when the sequencer is recording?

Re: performances?

29 Jun 2007, 21:16
You must be recording in PATTERN MODE ... (Flip past the 16th MIDI track in the record options and you'll start seeing all the possible pattern locations ... or just get into pattern and select a track ...

when you record the pattern ... just flip the jog wheel once to the performance you want ... press stop ... then copy the pattern into the MIDI sequencer part ... (use the COPY command in track edit) ... when playing the song, once the sequencer gets to the pattern, it will switch to the new performance ... you may have to try it a few times, but believe me, it DOES work ...

check back if it's still not working ...



. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Roland Fantom X7, Alesis Fusion 6HD+KP2, Novation X/A-Station 25, Alesis Micron+KP3

some tunes and whatnot ...
http://www.soundclick.com/bands/pagemusic.cfm?bandID=405125
Some tunes and whatnot ...

http://www.soundclick.com/bands/page_music.cfm?bandID=405125



some tunes and whatnot ...
http://www.soundclick.com/bands/pagemusic.cfm?bandID=405125

← Back to Fantom-S and Fantom-X