Fantom-G

Replacing an endbell on a G7

Replacing an endbell on a G7

16 Sep 2009, 15:01
Purchased my G7 via an Ebay store and it had a bit of damage on the endbell. Got a replacement endbell but Roland will not give any instructions as to who I can do the replacement (short of taking it to a service center...I know how to work a screw driver.)

Would anyone have the service manual of info as to how to do the deed?

Thanks,
Tom

Re: Replacing an endbell on a G7

16 Sep 2009, 16:16
Hi Vismus,

Could you explain to me what an endbell is?
Or please a picture?

I repaired many Fantom-G's but i have no idee what you mean.

Re: Replacing an endbell on a G7

16 Sep 2009, 16:39
Insilentio:

The end bells are the end pieces of the the keyboard casing.
I need to know what screws to remove and NOT remove to faciltate the replacement.
Have enclosed a pic of the replacement.

Thanks very much for the help.

Regards,
Tom Martin
obtmusic.com

Re: Replacing an endbell on a G7

16 Sep 2009, 22:23
Endbells! Fascinating!

Is that one word or two?

Inspired by Piaknowguy, here's the photo for those with a slower internet connection:

Image

This, of course, should not be confused with "bell end."

Image

Re: Replacing an endbell on a G7

17 Sep 2009, 06:56
Wombat:

Thanks for the technical advice. Hope to return the favor.

Re: Replacing an endbell on a G7

17 Sep 2009, 10:01
Insilentio:
Roland's actual part name is 'Side Cover L Assembly'. Part number is 73895101
Is a bit more complex that I thought it would be as an integrated metal frame.
Thanks in advance for the help,
Tom

Re: Replacing an endbell on a G7

17 Sep 2009, 10:01
I've got some drawings for you, i''l try to post them this evening

Re: Replacing an endbell on a G7

17 Sep 2009, 10:07
Insilentio:
Thanks very much. Will watch for your posts.
Think it's rather odd that Roland would sell me the replacement part but not give any info as to how and install it

Tom

Re: Replacing an endbell on a G7

18 Sep 2009, 07:31
They look like the same for a V-Synth - I replaced mine & it was easy.

Just remove the old screws - pull them off, then replace!

Re: Replacing an endbell on a G7

18 Sep 2009, 08:55
Actually, a Roland tech called and he intervened with the service department. They claim that it is not an easy job replacing the end cover on the G series and involves removing the left modulation panel. Lots of patience and about 2 hours of labor to do the job done. The actual assembly has to be totally replaced as the outside cover and interior metal framework are fastened together in several (inside) points. Alas, still don't know what screws to remove and which to leave to rotate the bottom away from the top.

Tom

Re: Replacing an endbell on a G7

18 Sep 2009, 09:39
To lift the bottem you have to remove all the srews from the bottom, than you can lift the whole plate.

Re: Replacing an endbell on a G7

18 Sep 2009, 11:22
Insilentio:

Thanks very much for all you help.
Regards,
Tom Martin
obtmusic.com

Re: Replacing an endbell on a G7

18 Sep 2009, 14:55
V,

These things are designed to be put together and taken apart and are all of modular manufacture..so I would not be put off by their service tech..

case in point: i was informed that to replace the display on my GW-7 would take 1.5hrs and must be done by a service center.. But, luckily my local service center allowed me to simply order the display thru them...saving me $130.

It took me all of 15mins start to finish.. with nothing more than a #1 and #2 pt screwdriver.. my biggest worry was laying the board down on its front!..

M38

>>
Actually, a Roland tech called and he intervened with the service department. They claim that it is not an easy job replacing the end cover on the G series and involves removing the left modulation panel. Lots of patience and about 2 hours of labor to do the job done. The actual assembly has to be totally replaced as the outside cover and interior metal framework are fastened together in several (inside) points. Alas, still don't know what screws to remove and which to leave to rotate the bottom away from the top
<<

Re: Replacing an endbell on a G7

20 Sep 2009, 11:01
Mystic:
Will probably take your advice and spring the case. I totally rebuilt a Yamaha KX5 remote controller. But you know how it is when you've just got a new toy...
Here's the quick fix. I masked of the side cover assembly, or as I called it, and 'endbell,' and sprayed it with a Krylon Chrome Aluminum paint, a perfect match to the original. Included a pic so you can judge.

Many thanks for all the tips,
Tom

← Back to Fantom-G